Guidelines for connecting through Bezeq International

Further to Prof. Reuven Cohen's letter, below are guidelines for researchers to set up a home router to connect via Bezeq International.

The support center is available 24 hours a day at 076-5555899
(Please identify as a Technion user with your ID number and your STAFF account usename)

 

 

D-link 2650U Router Setup Guide

 

Model: d-link 2650U

Step One: Enter the router for connection settings.

Open a browser and type in the address line: http://10.0.0.138

 

for url type http://10.0.0.138

In the window that opens, type in the username format: Admin
In the password format  type Admin.

If the default username and password (Admin) is changed on the router, please enter the username and password accordingly.

In the event of a router login failure, the router can be reset with a 30-second click on the reset button located on the back of the router.

After performing a reset, you must login to the router with Admin as username and password.

for username and password use Admin

Step 2: Router settings

In the left menu, click Advanced Setup

press Advanced Setup


Make sure that the line 0/8/48 is in the Port/Vpi/Vci field,
and press the EDIT button.

press EDIT

Please verify the following:

  • 0 is defined in the PORT field
  • 8 is defined in the VPI field
  • 48 is defined in the VCI field
  • UBR Without PCR is chosen in the Service Category option
  • make sure the option Enable Quality Of Service is not checked

To continue, click Next.

press Next

Verify that the PPP over Ethernet (PPPOE) option is checked

and LLC/SNAP-BRIDGING is checked in the Encapsulation Mode field

To continue, click Next.

press Next

 

Please fill in the following details:

  • PPP Username - enter the username in the following format: tec.user @iucc
    user=username at STAFF
  • PPP Password - enter the passowrd
  • Verify that the Enable NAT option is checked
  • Uncheck the Enable Firewall option
  • Verify that the Obtain default gateway automatically option is checked
  • Verify that the Keep alive PPP connection option is checked
  • Uncheck the Bridge Pppoe Frames Between WAN and Local Ports (Default Enabled) optionTo continue, click Next.

press Next

Verify that the Enable WAN Service is checked.

To continue, click Next.

press Next

To save the settings, click Save.

press Save

press Save/Reboot

To save settings and restart the router, please click Save/Reboot.

The router is restarting.
Please wait for the window announcing it up and running, then click OK.

press OK

D-link 2760U Router Setup Guide

 

Model: d-link 2760U

Step One: Enter the router for connection settings.

Open a browser and type in the address line: http://10.0.0.138

for url type http://10.0.0.138

In the window that opens, type in the username format: Admin
In the password format  type Admin.

If the default username and password (Admin) is changed on the router, please enter the username and password accordingly.

In the event of a router login failure, the router can be reset with a 30-second click on the reset button located on the back of the router.

After performing a reset, you must login to the router with Admin as username and password.

use Admin for username and password

Step 2: Router settings

In the left menu, click Advanced Setup

press Advanced Setup

Please click on WAN Service

press WAN Service

Make sure that the line 0/8/48 is in the Port/Vpi/Vci field,
and click the EDIT button.

press EDIT

click Next

press Next

Verify that the PPP over Ethernet (PPPOE) option is checked.
To continue, click Next.

press Next

Please fill in the following details:

  • PPP Username - enter the username in the following format: tec.user @iucc
    user=username at STAFF
  • PPP Password - enter the passowrd
  • Verify that the Enable NAT option is checked
  • Uncheck the Enable Firewall option
  • Verify that the Obtain default gateway automatically option is checked
  • Verify that the Keep alive PPP connection option is checked
  • Uncheck the Bridge Pppoe Frames Between WAN and Local Ports (Default Enabled) optionTo continue, click Next.

press Next

Click Next.

press Next

Please check  Obtain DNS info from a WAN interface
and click Next

press Next

To save the settings, please click Save.

press Save

press Save/Reboot

To save settings and restart the router, please click Save/Reboot.

The router is restarting.
Please wait for the window announcing it up and running, then click OK.

press OK

   

 

D-link 6740U Router Setup Guide - Version 1

 

Model: d-link 6740U Version 1

Step One: Enter the router for connection settings.

Open a browser and type in the address line: http://10.0.0.138

for url type http://10.0.0.138

In the window that opens, type in the username format: Admin
In the password format  type Admin.

If the default username and password (Admin) is changed on the router, please enter the username and password accordingly.

In the event of a router login failure, the router can be reset with a 30-second click on the reset button located on the back of the router.

After performing a reset, you must login to the router with Admin as username and password.

for username and password use Admin

Step 2: Router settings

Please click Setup

press Setup

Click on Wan Service and choose PPPOE Wan

press Wan Service and choose PPPOE Wan

Click on Edit on the first line in the window that opens.
In the first line, click on Edit where it says pppoe_0_8_48

press Edit

Verify that PPP Over Ethernet - PPPoE is checked and click on Next

press Next

Please fill in the following details:

  • PPP Username - enter the username in the following format: tec.user @iucc
    user=username at STAFF
  • PPP Password - enter the passowrdTo continue, click Next

press Next

Please verify that Obtain DNS server address automatically is checked and click on Next

press Next

Make sure that Selected WAN Interface pppoe_0_8_48/ppp0 is checked, then click Next

press Next

  When done, click Apply/Reboot

press Apply/Reboot

D-link 6740U Router Setup Guide - Version 2 / d-link 7850 / d-link 6850U

 

Model: d-link 6740U Version 2 / d-link 7850U / d-link 6850U

Step One: Enter the router for connection settings.

Open a browser and type in the address line: http://10.0.0.138

for url type http://10.0.0.138

In the window that opens, type in the username format: Admin
In the password format  type Admin.

If the default username and password (Admin) is changed on the router, please enter the username and password accordingly.

In the event of a router login failure, the router can be reset with a 30-second click on the reset button located on the back of the router.

After performing a reset, you must login to the router with Admin as username and password.

for username and password use Admin

Step 2: Router settings

Go to Setup, click on Wan Service and then on PPPOE WAN

press Wan Service and then PPPOE WAN

Click on EDIT in the first line

press Edit

Please fill in the following details:

  • PPP Username - enter the username in the following format: tec.user @iucc
    user=username at STAFF
  • PPP Password - enter the passowrdTo continue, click Next

press Next

. When done, click Apply/Reboot

press Apply/Reboot

Router Setup Guide - NETGEAR VVG2000NETGEAR DGN1000NETGEAR DGN834 / NETGEAR DGN2200

    

Model: NETGEAR VVG2000 / NETGEAR DGN1000 / NETGEAR DGN834 / NETGEAR DGN2200

   

Step One: Enter the router for connection settings.

Open a browser and type in the address line: http://10.0.0.138

for url type http://10.0.0.138

In the window that opens, type in the username format: Admin
In the password format  type Admin.

If the default username and password (Admin) is changed on the router, please enter the username and password accordingly.

In the event of a router login failure, the router can be reset with a 30-second click on the reset button located on the back of the router.

After performing a reset, you must login to the router with Admin as username and password.

for username and password use Admin

Step 2: Router settings

In the left menu, under Setup, click on Basic Settings

press Basic Settings

  1. In the Does Your Internet Connection Require A Login field? Check Yes
  2. in the Encapsulation field enter PPPOE
  3. in the Login field  enter the username in the following format: tec.user@iucc
    user = username at STAFF
    TEC = University name
  4. in the Password field enter the password
  5. in the Internet IP Address field check Get Dynamically From ISP
  6. in the Domain Name Server Address(DNS) field check Get Automatically From ISP
  7. in the NAT (Network Address Translation) field check Enable

To save click on Apply

press Apply

NETGEAR VEGN2610 Router Setup Guide0

 

Entering the router interface:

Open a browser and enter the router at address: http://10.0.0.138

for url type http://10.0.0.138

In the window that opens, type in the username format: Admin
In the password format  type Admin.

If the default username and password (Admin) is changed on the router, please enter the username and password accordingly.

In the event of a router login failure, the router can be reset with a 30-second click on the reset button located on the back of the router.

After performing a reset, you must login to the router with Admin as username and password.

for username and password use Admin

Step 2: Router settings

  1. In the Does Your Internet Connection Require A Login field? Check Yes
  2. in the Internet Service Provider field enter PPPOE
  3. in the Login field  enter the username in the following format: tec.user@iucc
    user = username at STAFF
  4. in the Password field enter the password
  5. in the Internet IP Address field check Get Dynamically From ISP
  6. in the Domain Name Server Address(DNS) field check Get Automatically From ISP
  7. in the NAT (Network Address Translation) field check Enable

To save click on Apply

 

press Apply

עודכן: 10/05/2020 , 10:37